MN103S65G internal ram 4 k-byte sram internal rom 128 k-byte type MN103S65G minimum instruction execution time 25 ns (at 4.3 v to 5.5 v, 10 mhz internal regulator used) 25 ns (at 3.0 v to 3.6 v, 10 mhz) *at internal 4 times oscillation used) package lqfp080-p-1414a *lead-free maf00010aem interrupts ? 9 external interrupts 42 internal interrupts (watch dog timer, timer, serial i/f, pwm, a/d, system error) timer counter eight 8-bit timers interval timer, event counter, cascading four 16-bit timers interval timer, event counter, pwm output, double buffer watch dog timer serial interface uart (full duplex) / synchronous interfaces selective: 3 i/o pins exclusive: 2, selective: 48 i/o a/d inputs 10-bits, 2 inputs: 2, 6 inputs: 1 minimum conversion time 1.5us selective: 10 input 50 10 pwm 3-phase pwm output 16-bit counter, triangular waveform or jigsaw waveform dead time setup, double buffer electrical characteristics t.b.d.
test1 test2 test3 osco osci v ss pv ss pv dd v dd2 v dd lon p07/nrst p10/irq04 p11/irq05 p12/irq06 p13/irq07 p14/irq08 p17/sbo2 p20/sbt2 p21/sbi2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 p43/tm9bi p42/tm9ai p41/tm8bio p40/tm8aio p37/tm7io p36/tm6io p35/tm5io v dd p34/tm4io v ss p33/tm3io p32/tm2io p31/tm1io p30/tm0io p27/sbi0 p26/sbt0 p25/sbo0 p24/sbi1 p23/sbt1 p22/sbo1 p64/pwm12 p65/pwm13 p66/pwm14 p67/pwm15 p74/irq00 p75/irq01 p76/irq02 p77/irq03 p80/adin00 p81/adin01 v ss p82/adin10 v dd p83/adin11 p84/adin20 p85/adin21 p86/adin22 p87/adin23 p90/adin24 p91/adin25 p63/pwm11 p62/pwm10 p61 p60 p57/npwm02 p56/pwm02 p55/npwm01 p54/pwm01 p53/npwm00 p52/pwm00 v dd p51/tm10bo v ss p50/tm10ao v dd2 v pp p47/tm10bi p46/tm10ai p45/tm9bo p44/tm9ao MN103S65G maf00010aem pin assignment lqfp080-p-1414a * lead-free MN103S65G support tool flash memory built-in type type mn103sf65g rom 128 k-byte ram 4 k-byte sram minimum instruction execution time 25 ns (at 4.3 v to 5.5 v, 10 mhz internal regulator used) 25 ns (at 3.0 v to 3.6 v, 10 mhz) package lqfp080-p-1414a *lead-free on board debugger px-odb103s-do in-circuit emulator px-ice-103s52
request for your special attention and precautions in using the technical information and semiconductors described in this material (1) an export permit needs to be obtained from the competent authorities of the japanese government if any of the products or technical information described in this material and controlled under the "foreign exchange and foreign trade law" is to be exported or taken out of japan. (2) the technical information described in this material is limited to showing representative characteristics and applied circuits examples of the products. it neither warrants non-infringement of intellectual property right or any other rights owned by our company or a third party, nor grants any license. (3) we are not liable for the infringement of rights owned by a third party arising out of the use of the technical information as described in this material. (4) the products described in this material are intended to be used for standard applications or general elec- tronic equipment (such as office equipment, communications equipment, measuring instruments and house- hold appliances). consult our sales staff in advance for information on the following applications: ? special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combus- tion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. ? any applications other than the standard applications intended. (5) the products and product specifications described in this material are subject to change without notice for modification and/or improvement. at the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date product standards in advance to make sure that the latest specifica- tions satisfy your requirements. (6) when designing your equipment, comply with the guaranteed values, in particular those of maximum rat- ing, the range of operating power supply voltage, and heat radiation characteristics. otherwise, we will not be liable for any defect which may arise later in your equipment. even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (7) when using products for which damp-proof packing is required, observe the conditions (including shelf life and amount of time let standing of unsealed items) agreed upon when specification sheets are individually exchanged. (8) this material may be not reprinted or reproduced whether wholly or partially, without the prior written permission of matsushita electric industrial co., ltd. 2003 sep
|
